When a kitchen fire gets knocked down, the water left behind keeps damaging your Studio City home. Our water damage remediation after fire in Studio City, California starts with emergency water removal, structural drying, and odor control, then moves into full fire water damage restoration in Studio City. We work with your insurance, document everything, and get your house dry and safe again.
Water damage remediation after fire in Studio City, California is the trade of extracting firefighting water, drying structural cavities, and neutralizing smoke and soot residue before mold takes hold. Fire hoses push 100 to 250 gallons per minute into a house, and that water travels fast: through ceiling drywall, into wall cavities, under wood subfloor, and down into crawl spaces. We use moisture meters, thermal imaging cameras, and boroscopes to map where the water actually went, not just where the floor looks wet.
Most Studio City calls we take start the same way: a kitchen fire, a garage fire, or a brush fire that gets knocked down by LAFD, and then the homeowner discovers water stains spreading across the ceiling two days later. If you search for water damage remediation after fire near me Studio City, you need a crew that treats the water problem as seriously as the fire damage. We handle emergency water damage remediation after fire Studio City homeowners can schedule same-day, including nights and weekends.
Every fire loss is different, but the core scope of water damage remediation after fire in Studio City, California follows the same sequence: stop the water, dry the structure, clean the smoke, and prove it is dry. Here is what is included in a standard job, and what we handle as an add-on when the loss calls for it.
We pull standing water with truck-mounted and portable extraction units, then remove saturated carpet padding, insulation, and ceiling drywall that cannot be saved. In most Studio City jobs, extraction starts within 2 to 4 hours of your call.
We use moisture meters, thermal imaging cameras, hygrometers, and boroscopes to find hidden water in wall cavities, subfloor, and crawl spaces. Every reading is photographed and logged in Xactimate format for your insurance adjuster.
We place Dri-Eaz and Phoenix Restoration Equipment air movers and dehumidifiers based on the size and layout of the wet area. Desiccant units go in for crawl spaces. We monitor daily and adjust until moisture content meets the dry standard.
We apply antimicrobial solution to wet framing, subfloor, and drywall edges to stop mold growth after water damage. Air scrubbers with HEPA filtration run throughout the drying phase to keep spores from spreading to unaffected rooms.
After the structure is dry, we clean soot from surfaces and run ozone generators and thermal fogging to neutralize smoke odor. This is the step that keeps your house from smelling like a fire weeks later, and it is included in every full-scope job.
You call (833) 321-7153 and describe what happened. We ask about the fire location, how long the water has been sitting, and whether power is safe to restore. A crew is dispatched with extraction and drying equipment, usually arriving within 60 to 90 minutes anywhere in Studio City.
We walk the house with a moisture meter, thermal imaging camera, and hygrometer. We check wall cavities with a boroscope, look under baseboards, and pull carpet padding samples. You get a written scope with photos before we start drying, so there are no surprises.
Standing water comes out first using truck-mounted and portable water extraction units. We remove saturated carpet padding, ceiling drywall, and insulation that cannot be saved. Salvageable contents get moved to a dry area of the house or a staging spot in the garage.
We set Dri-Eaz and Phoenix Restoration Equipment air movers and dehumidifiers based on the size of the wet area. Desiccant dehumidifiers go in for tight crawl spaces. We check readings daily and adjust equipment until moisture content matches a dry standard, usually 3 to 5 days.
Once the structure is dry, we apply antimicrobial solution, run ozone generators and air scrubbers for smoke odor, and clean soot from surfaces. You get a final moisture report, photos, and a walkthrough before we pull equipment. Most jobs close out in 5 to 7 days.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Finds hidden moisture behind walls, under floors, and in ceiling cavities without tearing out finished surfaces. Essential after a fire when water has traveled far from the visible wet area.
Measures moisture content in drywall, wood subfloor, and framing, and tracks relative humidity in the air. We use readings to decide when drying is complete, not guesswork.
A small camera we feed into wall cavities and crawl spaces to see water damage and early mold growth without opening the whole wall. It saves money on unnecessary demolition.
High-velocity air movers that evaporate moisture from surfaces so dehumidifiers can pull it out of the air. We position them based on room layout and wet material type.
Pulls moisture from the air in cool, tight spaces like crawl spaces and basements where refrigerant dehumidifiers lose efficiency. Common in Studio City hillside homes.
Ozone neutralizes smoke odor at the molecular level after drying. Air scrubbers with HEPA filtration run during the job to keep mold spores and soot particles out of clean rooms.
Truck-mounted and portable units that pull standing water out of carpet, hardwood, and concrete. The faster we extract, the less material has to be replaced.
A grease fire was knocked down in under 10 minutes, but the hose water ran under the cabinets and soaked the wood subfloor in the dining room. The homeowner noticed cupping two days later and called us. Moisture readings showed the wall cavity behind the range was still at 28 percent.
We extracted standing water, removed wet pad, opened the toe kicks, and dried the cavity with air movers and a desiccant dehumidifier. Five days later, readings were at 9 percent. The cabinets were saved and the subfloor did not need replacement.
A garage fire sent water down the sloped driveway and into a below-grade storage room. The homeowner waited three days before calling because they thought it would dry on its own. By then, mold was visible on the base of two wall studs and the concrete slab was still wet.
We pumped out standing water, removed contaminated drywall and insulation, applied antimicrobial solution, and ran desiccant dehumidifiers for four days. Final readings confirmed the slab and framing were dry. The storage room was back in use within a week.
A bedroom fire was contained quickly, but the ceiling below was soaked and sagging by the next morning. The homeowner called us at 11 p.m. and we arrived around 12:30 a.m. Thermal imaging showed water had traveled six feet beyond the visible stain.
We cut out the sagging drywall, extracted water from the ceiling cavity, and dried the framing above with air movers. Air scrubbers ran for three days to clear smoke particles. The ceiling was repaired and repainted in six days.
Fire damage is obvious. The water damage that follows is what surprises homeowners. These are the problems we see most often and how we fix them.
Ask a pro →We use thermal imaging cameras and boroscopes to find water behind walls without tearing the whole room apart. We cut targeted access points, dry the cavity, and apply antimicrobial solution before closing it back up.
We open the ceiling, extract standing water, dry the framing above, and repair the drywall. In Studio City homes with original plaster ceilings, we take extra care to dry slowly and avoid cracking the surrounding finish.
We pump out standing water, run desiccant dehumidifiers, and treat joists and subfloor with antimicrobial solution. If ventilation is poor, we recommend encapsulation to keep the space dry long-term.
We clean soot from surfaces, run air scrubbers during drying, and finish with ozone generators and thermal fogging. This combination neutralizes odor at the source instead of masking it with fragrance.
Most residential jobs in Studio City run $2,800 to $9,500 in 2026, depending on how far the water traveled and how much drywall or flooring has to come out. A single-room kitchen fire with limited water spread often lands near the low end. Whole-house losses with crawl space flooding push higher. We provide a written scope and bill your insurance carrier directly.
We do. Water Damage Restoration Studio City handles fire water damage restoration in Studio City California, including emergency water extraction, structural drying, soot cleanup, and odor control. We are IICRC certified, licensed through the CSLB, and dispatch crews 24/7 from our Studio City base. Call (833) 321-7153 and we will confirm an arrival window.
Extraction and setup take one day. Structural drying usually runs 3 to 5 days with daily monitoring. Odor control, cleaning, and final walkthrough add another 1 to 2 days. Most Studio City jobs are fully closed out in 5 to 7 days, though hillside homes with crawl space moisture or slab leaks can take 10 days or longer.
Yes. We document every affected surface with photos, moisture readings, and Xactimate line items, then communicate directly with your adjuster. You typically pay your deductible and we bill the carrier for the rest. If your policy includes ALE coverage, we can also note temporary housing needs in the file so your adjuster sees the full picture.
flood restoration servicesWhen firefighting water overwhelms a room faster than extraction can keep up, our flood restoration services handle the volume. We bring truck-mounted extraction and desiccant dehumidifiers to pull gallons out of carpet, pad, and subfloor before they wick into walls.Explore →
emergency water removalEmergency water removal is the first step of any water damage remediation after fire job. We pull standing water within hours of your call, which stops it from spreading under baseboards and into adjacent rooms. Fast removal is the difference between drying a room and rebuilding it.Explore →
mold remediation after water damageMold growth after water damage is the second disaster after a fire. We inspect wall cavities with boroscopes, apply antimicrobial solution, and remove contaminated drywall and insulation. If mold is already visible, we contain the area with polyethylene sheeting before disturbing it.Explore →
water leak restorationSometimes a fire exposes a pre-existing burst pipe or slab leak that was already weeping. Our water leak restoration crews find the source with thermal imaging, repair or isolate the line, and dry the surrounding structure so you are not dealing with a second water loss weeks later.Explore →
emergency water cleanupEmergency water cleanup covers the messy aftermath: wet carpet padding, soaked insulation, and standing water in low spots. We remove what cannot be saved, extract what can, and set drying equipment the same day so your Studio City home starts moving toward dry.Explore →
water extractionWater extraction is the heavy-lifting phase. We use truck-mounted and portable water extraction units to pull water out of carpet, hardwood, and concrete. In Studio City homes with wood subfloor, fast extraction prevents warping and cupping that shows up days later.Explore →
water damage mitigationWater damage mitigation is about stopping the damage from getting worse. After a fire, that means extracting water, removing saturated materials, and controlling humidity so mold cannot colonize. We treat mitigation as the foundation the rest of the restoration is built on.Explore →
toilet overflow cleanupA toilet overflow during or after a fire loss adds contaminated water to an already bad situation. We treat it as Category 2 or Category 3 water, remove affected materials, and apply antimicrobial solution. That protects your family from bacteria while the structure dries.Explore →Every hour the water sits, the damage gets deeper and the repair bill gets bigger. We are IICRC certified, CSLB licensed, and available 24/7. Call (833) 321-7153 and we will dispatch a crew to your Studio City address with extraction and drying equipment ready to go.
Call Now (833) 321-7153 →Reach us any hour at (833) 321-7153 for emergency water removal, extraction, or drying. We answer live, day or night, and dispatch a crew right away. For non-emergency estimates, email info@waterdamagerestorationstudiocity.com and we will get back to you the same business day.